NISSAN MAP OVERHEAD DOME DISPLAY INSTALL
NISSAN MAP OVERHEAD DOME DISPLAY DRIVER
NISSAN MAP OVERHEAD DOME DISPLAY FULL

NISSAN MAP OVERHEAD DOME DISPLAY DRIVER

Dome:В This light is on the roof and fits either in the center or between the driver and passenger.

These are the models that all year vehicles should have and you will be able to find replacement parts or kits for. You may tend to focus more on the external lights, but the inside of your car has many standard lights and you can add more if you wish.

Where are the Different Places that Interior Lights Are Fixed? You can easily find replacement parts so you can get your interior lighting back to the way it should be. Thankfully, there is an easy solution when the interior lights of your Nissan Xterra stop working. The hardest part for me was de-pinning the harness as it took a few (15) minutes to figure out how it works.What Can I Do When My Interior Lights Stop Working? If you take your time it's not difficult. You can then see the clips for the lower piece and pop them out with an upholstery tool. Then pull down or use an upholstery tool to pop out the clips that attach vertically into the roof. Remove the larger piece first by popping it away from the small strip.

The upper striker plate cover is two pieces. I taped the harness to the headliner before gluing as a temporary hold to make it easier.

NISSAN MAP OVERHEAD DOME DISPLAY INSTALL

This gave me enough room to install the bracket and glue down the wiring harness. But first remove the vertical light gray strip below it, since this has an overlapping clip that is attached to the a-pillar plastics.Д«e careful to not pull down more than 4-5' on the headliner since it is attached in the back. The A pillars are clipped in near the top, and then will rotate toward you and lift out of the dash area. Try not to tear the living hinges on the screw covers. After removing the phillips screw, slide the sun visor bracket rearward and it will unhook and drop out of the mounting hole. To remove the sun visor mount, carefully pop off the cover near the hinge. To remove the sun visor clips, rotate them clockwise 90 degrees. You can also see all of the plastics I removed here. It looks 100% oem and when I showed one of my friends he was surprised and asked вЂњWait, that didnвЂ™t come in the truck?вЂќДЄ few more photos including the finished product. I managed to not break any plastic parts, clips, or harness damage. I forgot to take photos during the de-pinning and of the wiring installed on the a-pillar. Reinstall all plastic parts that were removed. Install both dome lights, and then tuck the headliner back into the door weather seal. I used the sun visor resting clips to hold the liner up in the right position while doing this.ДЁ. I cut a starting hole, and then slowly worked my way outwards until tracing around the mounting opening in the metal bracket. Measure distance from the windshield to center of bracket, and then push up the headliner and mark the same distance. Plug in new harness, snapping it in up the A-pillar and then hot glueing the new harness to the headliner so it does not rattle around.Д§. Note rear light requires chassis ground.Д¦. Then you can release each wire at a time.Д¬onfirm wiring works. This is delicate work, and requires removing the front cover plate and also lifting the center clip up. So, de-pin both plugs, and switch the new harness over to the plug from the old harness. While the truck side harness has the correct wires, the new harness has a larger plug. If you just yank it off, the headliner may get torn since the glue is pretty strongДҐ. Pull headliner down a few inches and install the dome light bracket.ДЄlso carefully remove the old wire harness which is glued down to the headlinerД¤. Carefully pop the headliner out from the door seals.ДЈ. Remove grab handles, A-pillar plastics, sun visors, rear clips near the 3rd brake light caps, upper striker plate covers, rear dome light.Дў. I did not remove the headliner entirely, but left it supported at the very back edge only so I did not have to remove the rear seats and seat belts.

Start by removing plastics supporting the headliner.

NISSAN MAP OVERHEAD DOME DISPLAY FULL

You could get by without the full wire harness and just a pigtail, but you would have to run a ground to the chassis, and also tap into the rear dome light wires.ДЎ. This is the dome light only version, not the light with sunglasses holder. Different parts may work, just listing what I used. I went to the local Nissan junkyard for parts, and these were 'free' with some other parts I bought. I installed a dome/map light in the front of my 2007 KC XE 4 cyl and decided to add a writeup.

Nissan map overhead dome display